FUTABA 3PM 2.4GHz MX RC Model Transmitter & R603FS Receiver TS830

USD206.5USD215.9 (-4%)

Out of stock

FUTABA 3PM 2.4GHz MX RC Model Transmitter & R603FS Receiver TS830. This is 100% Brand new item and we can ship this item to worldwide.

Compare
SKU: TS830 Category:

Introduction
Thank you for interesting a 3PM-2.4GHz MX system. This system is based on the combination of the newly developed 2.4GHz transmitter and its correspondent receiver. The system utilizes the 2.4GHz-SS radio communication and an ultra small antenna. In addition, the system inherits Futaba’s unique HRS (High Response System).

Transmitter Specifications
Brand: Futaba
Item: RC Model Transmitter and Receiver
Communication Method: One-way operation system
Mode: PPM, HRS (Auto-detect)
Maximum Operating Range: 80m (Optimum condition)
For Safety: F/S, B-F/S, ID
Transmitting Frequency: 2.4GHz band
Channel: 3ch
Current Drain: 250mA or less
Transmission Antenna: 1/2 di-pole

Transmitter Features
2.4GHzSS (Spread Spectrum) radio communication system.

Frequency channel setting unnecessary. – Sifting the channels within the 2.4GHz band automatically, this systemminimixes the interference from other 2.4GHz systems.

Accepts no unwanted signals by using ID code.

The function “Auto-Detect” is utilized to automatically determine whichmode is active, HRS or PPM mode.

Diversity antenna

Simple segment type LCD display and four edit keys for easy data setup

10 models memory – Model names can use up to 3 letters, numbers and symbols so that easily understood names can be set. Model copy function simplifies creation of a model memory with different fine setups.

Two function groups: Frequently used functions / System functions – Frequently used functions can be easily called from the initial screen with Select Key (SEL).

4WS mixing (4WS) – This mixing is used with Crawler and other 4WS Specifications cars. The 1st channel controls the front side steering and the 3rd channel controls the rear side steering. The operation mode of the front and rear wheels can be switched by switch (SW1).

Brake mixing for large cars (BMX) – Brake mixing of the front and rear wheels of 1/5GP car, etc. has balance adjustment functions.

Steering dual rate (D/R-ST) – Steering angle can be adjusted with digital trim lever.

Anti-skid Braking System (ABS) – This function applies the brakes so that the tires of gasoline engine cars, etc. do not lose their grip on the road even when braking at corners.

Throttle acceleration (ACC) – Gasoline engine cars have a time lag before the clutch and brakes are connected. The ACC function minimizes this time lag.

Steering speed (SPD) – When you sense that the steering servo is too fast, etc., the servo operating speed (direction that suppresses the maximum speed) can be adjusted.

Racing timer (TIMER) : Up timer or Down timer can be selected. – A lap time can record 100 lap times and the total time. The timer can also be started automatically by trigger operation. The race time can be set.

Digital trim : Steering trim, Throttle trim, Steering D/R, Throttle ATL – The current position is displayed on the LCD screen for about three seconds when each digital trim is operated.

Function select lever function (FNC-DT1/DT2/DT3/DT4) – This function assigns a function to levers (digital trims, grip levers). Trim positioning at each model call is unnecessary because all the levers are digital.

Digital trim step function (STP-DT1/DT2/DT3/DT4) – The digital trim (DT1/DT2/DT3/DT4) step amount can be adjusted by means of the function.

Function select switch function (FNC-SW1/SW2) – This function assigns a function to the two installed switches.

Condition 2 Selection – In specific functions, two rates can be set up, and switched with SW1 switch simultaneously during a run.

NEW design considers operability and weight balance

Adjuster function (ADJ) – Steering wheel and throttle trigger neutral position and operating angle correction can be applied.

Tension adjustment function – The wheel tension can be adjusted from the outside.

Trigger stopper function (mechanical ATL)

High luminosity blue LED pilot lamp – You can select your desired brightness of the pilot lamp. (Four steps)

Receiver Specifications
Brand: Futaba
Item: RC Model Transmitter and Receiver
Dimensions: 39 x 26 x 14mm
Frequency: 2.4GHz
Channel: 3ch
Power Requirement: 6V Nicd battery

Item Included: 1 x Futaba RC Model 3PM 2.4GHz MX R/C Hobby Transmitter & R603FS Receiver TS830

Brand

FUTABA

Additional information

Weight876 g
Dimensions45 × 25 × 20 cm
Submit your review

Your email address will not be published.

Reviews

  1. by Member id biomen50 ( Feedback Score Of 29)

    great seller, fast shipping . well done

  2. by rycho_nor ( 68)

    Great item and quick shipping. Thanks 🙂

  3. by bobbymalta73 ( 152)

    GOOD SELLER ITEM AS DESCRIBED,VERY HAPPY.

See It Styled On Instagram

    Instagram did not return a 200.
Select your currency
EUR Euro
USDUnited States (US) dollar
English

Main Menu