GT POWER X-CHARGER 606D LiPo Li R/C Hobby Digital Charger (EU Plug) BC045

Introduction
Thank you for interesting the X-CHARGER 606D charger. This is a rapid charge / discharger with built in balancer, computerised with micro-oprocessor and specialised operating software.

Specifications
Operating Voltage Range: DC 10 – 18V, AC in: 100 – 240V, 50/60Hz
Circuit Power: Max. 50W for charging, Max. 5W for discharging
Charge Current Range: 0.1 – 6A
Discharge Current Range: 0.1 – 1A
Current drain for balancing Li-po: 300mAh/cell
NiCd/NiMH battery cell count: 1 – 15 Cells
Li-ion/Polymer Cell Count: 1 – 6 Series
Pb Battery Voltage: 2 – 20V
Dimensions: 134mm x 147mm x 42mm
Packet Includes: Multifuctional Connector

Features
Optimized operating software
When charging or discharging, It has an `AUTO` function that sets the feeding current automatically. Especially for Lithium batteries, it can prevent the over-charging can lead to an explosion by users fault. Every program in the unit is controlled with mutual links and communication for every possible error so it introduces a maximum safety. These can be set at users option.

Special recharge plugsport for receiver, transmitter and igniter charger. And for frequently used charger port such as multi purpose crocodile pin etc.

It provides most convenient balance charge port for Lithium batteries, with separated 3,4,5,6 charge port, and external reverse connector.

High-power and high-performance circuit
It employs the circuit that has maximum output power of 50W. As a result it can charge or discharge up to 15 cells of NiCd/NiMH and 6 series of Lithium batteries with maximum current of 6.0A. Furthermore the cooling system is so efficient that can hold such a power without any trouble of running the CUP or the operating program.

Individual voltage balancer for Lithium batteries inside
It has an individual-cell-voltage balancer inside. This does not require any extra balancer separately when charging Lithium batteries (Lilo/LiPO/LiFe) for cell voltage balancing.

Balance individual cells on discharge
It also can monitor and balance individual cells of the Lithium battery pack during the discharge process. If the voltage of any one cell varies abnormally, the process will be stopped with the error message.

Accept various types of Lithium battery
It can accept three types of Lithium batteries – Lilo, LiPo and LiFe. They have different characteristics by their chemistry. You can select any one of them that you are going to process before the job. For their specifications, refer `Warnings and safety notes` section. 

Lithium battery `Fast` and `Storage` mode
You can charge Lithium battery for special purposes. `Fast` charge reduces the charging time of Lithium battery and `storage` mode controls the final voltage of the battery to be suit for long time storage.

Maximum safety
Delta-peak sensitivity: The automatic charge termination program works on the principle of the Delta-peak voltage detection. (NiCd/NiMH)

Auto-charge current limit: When charging NiCd or NiMH at `AUTO` current mode, you can set the upper limit of change current to avoid from high current charging. This is very useful when charging the low impedance and small capacity NiMH battery in `AUTO` mode.

Capacity limit: The changing capacity always calculated by multiple of the charging current and time. If the charging capacity exceeds the limit the process will be terminated automatically when you set the maximum value.

Processing time limit: you can also restrain the maximum process time to prevent form any possible defect.

Input power monitor: To protect the car battery using as input power from being damaged the voltage of it always monitored. If it drops below the lower limit the process will be ended automatically.

Automatic cooling fan: The electric cooling fan comes into action automatically only when the internal temperature of the unit is raised.

Data store / load
For users convenience it can store maximum 5 data of different batteries. You can establish the data contains program setting of the battery to charge or discharge continually. These data can be called out at any time you need and the process can be executed without program setting.

Cyclic charging / discharging
Perform 1 to 5 cycles of charge>discharge or discharge>charge continually for battery refreshing and balancing.